PDA

View Full Version : Proud to have 2"...


tie6044
05-24-2007, 09:30 AM
Shafts :D Finally upgraded my front to OEM's 2" shafts with a locker. These things are impressive, here are a couple pics.

http://i163.photobucket.com/albums/t295/tie6044/OEM1.jpg

http://i163.photobucket.com/albums/t295/tie6044/OEM2.jpg

http://i163.photobucket.com/albums/t295/tie6044/OEM3.jpg
SuperDirty
05-24-2007, 09:38 AM
VIOLATOR

Sweet was your front open B 4? Were your front shafts stock or were they OEM Stock replacments?
tie6044
05-24-2007, 09:47 AM
My front was open but the shafts were Randy's upgraded replacements.
SuperDirty
05-24-2007, 09:49 AM
That fawker should really honk now with the locker. Did you just trade your shafts in then?
tie6044
05-24-2007, 09:57 AM
No I still have them.
SuperDirty
05-24-2007, 10:03 AM
Interesting
MrClemons
05-24-2007, 10:46 AM
very nice, id really like to see someone break one of those!
tie6044
05-24-2007, 10:54 AM
very nice, id really like to see someone break one of those!


I'm going to try this weekend but from what I've heard they are really tough to break.
SuperDirty
05-24-2007, 11:41 AM
For unbreakable Rockwell shafts check out
www.ouversonengineering.com ??????
MrClemons
05-24-2007, 12:26 PM
For unbreakable Rockwell shafts check out
www.ouversonengineering.com ??????

lol



tie didnt dibble break a 2inch?
leadfoot
05-24-2007, 01:32 PM
tie6044 if you are going to sell your other shafts let me know.
kxracer116
05-25-2007, 08:09 AM
Damn them things are beefy lookin!
HELLRAISER
05-25-2007, 09:48 AM
Shafts :D Finally upgraded my front to OEM's 2" shafts with a locker. These things are impressive, here are a couple pics.




WEAK:poke: Just kidding. Looks awsome man now when you get stuck this weekend your really get stuck.:poke:
tie6044
06-04-2007, 09:36 AM
WEAK:poke: Just kidding. Looks awsome man now when you get stuck this weekend your really get stuck.:poke:

What was this "getting stuck" thing you were talking about?? :poke: :D
MrClemons
06-04-2007, 03:30 PM
What was this "getting stuck" thing you were talking about?? :poke: :D

hahaha

so did you have to machine your housing to get the shafts to fit?
HELLRAISER
06-04-2007, 03:32 PM
What was this "getting stuck" thing you were talking about?? :poke: :D

You did good:D
tie6044
06-04-2007, 03:37 PM
hahaha

so did you have to machine your housing to get the shafts to fit?

Not in the front, just the spindles and the carrier halves, which are both removable. The rear must be machined because the spindles are part of the housing itself. Randy had the parts machined for me already and I just swapped him my stock pieces. All his components are really top notch stuff.
MINN 55
06-05-2007, 05:32 AM
You Guys Are Talking About Getting Stuckthis Weekend Where Is The Run At